Harbor Freight Tools OBD II & CAN Code Reader with Multilingual Menu Handbuch

Owner’s Manual & Safety InstructionsSave This Manual Keep this manual for the safety warnings and precautions, assembly, operating, inspection, ma

3. Using the Code Reader 3.1 Tool Description ① OBD II CONNECTOR -- Connects the code reader to the vehicle’s Data Link Connector (DLC). ② LCD D

93.2 Specifications 1) Display: Backlit, 128 x 64 pixel display 2) Operating Temperature: 0 to 60°C (32 to 140 F°) 3) Storage Temperature: -20 t

3.6 Product Setup The code reader allows you to make the following adjustments and settings: 1) Language: Selects desired language. 2) Unit of measu

2) Use SCROLL button to select the desired language and press ENTER/EXIT button to save your selection and return to previous menu. …………………Language…

Contrast Adjustment 1) From System Setup menu, use SCROLL button to select Contrast, and press ENTER/EXIT button. …………….System Setup………… …….

133.7 Vehicle Coverage ITEM 98568 OBDII/EOBD Code Reader is specially designed to work with all OBD II compliant vehicles, including those equipped w

144. OBD II Diagnostics When more than one vehicle control module is detected by the scan tool, you will be prompted to select the module where the

……………. System Status…………… … Codes Found 1 Monitors N/A 4 Monitors OK 3 Monitors INC 3 15

z The control module number, sequence of the DTCs, total number of codes detected and type of codes (Generic or Manufacturer specific, Stored or Pend

...Diagnostic Menu... ... 2/6 1) Read Codes ►2) Erase Codes 3) Freeze Frame 4) I/M Readiness 2) A warn

Table of Contents 1. Safety Precautions and Warnings...12. General Information ...

...Diagnostic Menu... ... 3/6 1) Read Codes 2) Erase Codes ►3) View Freeze Frame 4) I/M Readiness z If

19z The number “x/x” to the upper right corner of the screen indicates total number of screens the retrieved freeze frame covers and sequence of cur

...Diagnostic Menu... .. 4/6 1) Read Codes 2) Erase Codes 3) View Freeze Frame ► 4) I/M Readiness 2

4) Use SCROLL button to view the status of the MIL light (“ON” or “OFF) and the following monitors: z Misfire monitor -- Misfire monitor z Fuel Sys

4.5 Viewing Vehicle Information The Vehicle Info. function enables retrieval of the Vehicle Identification No. (VIN), Calibration ID(s), Calibration V

z Use SCROLL button to select a module, and press ENTER/EXIT button. 3) Wait a few seconds while the code reader reads vehicle information. …

...Diagnostic Menu... ... ... 6/6 5) Vehicle Info. ►6) Exit 24 2) A warning message comes up asking

11. Safety Precautions and WarningsTo prevent personal injury or damage to vehicles and/or the codereader, read this instruction manual first and obse

22. General Information2.1 On-Board Diagnostics (OBD) II The first generation of On-Board Diagnostics (called OBD I) was developed by the California A

3 2.3 Location of the Data Link Connector (DLC) The DLC (Data Link Connector or Diagnostic Link Connector) is the standardize

2.4 OBD II Readiness Monitors An important part of a vehicle’s OBD II system is the Readiness Monitors, which are indicators used to find o

5operated under specific conditions before the monitor is ready. These monitors are termed non-continuous monitors and are listed below: 1) EGR Syst

62.6 OBD II Definitions Powertrain Control Module (PCM) -- OBD II terminology for the on-board computer that controls engine and drive train. Malfu

7Freeze Frame Data -- When an emissions related fault occurs, the OBD II system not only sets a code but also records a snapshot of the vehicle opera