Harbor Freight Tools 46813 Bedienungsanleitung

10" TABLE SAWModel 46813ASSEMBLY ANDOPERATING INFORMATION3491 Mission Oaks Blvd., Camarillo, CA 93011Visit our Web site at http://www.harborfreig

3. Attach one Short Leg Brace (part #9B) to the lower mounting holes in two Legs(part #4B), using one Carriage Bolt (part #5B), one Washer (part #3B),

END BRACE (#6B)MOUNTING HOLESEND BRACE (#6B)HEXNUT(#2B)WASHER(#3B)BASE(#1G)HEX HEADBOLT (#8B)BASE(#1G)FIGURE DTo Assemble The Extension Tables:1. With

EXTENSIONTABLE (#5H)HEX HUT(#13H)HEX HEAD BOLT(#11H)WASHER(#12H)10” TABLE SAWEXTENSIONTABLE (#5H)HEXNUT(#13H)SQUAREHEAD BOLT(#10H)EXTENSIONTABLE (#5H)

3. NOTE: The back side of the Front Rail (part #7H) has two slots. Slide the upperslot of the Front Rail over the Square Head Bolts (part #10H). (S

BASE (#1G)(RIGHT EDGE)EXTENSION TABLE (#5H)456789SCALE (#6H)7-1/8” MARK, RIGHT SCALE3. Loosely attach a Washer (part #12H) and Hex Nut (part #13H) to

10” TABLE SAW/EXTENSION TABLES (#5H)(REAR EDGES)REAR RAIL (#3H)SLOTSQUARE HEADBOLT (#10H)WASHER (#12H)HEX NUT(#13H)FIGURE J5. Wrench tighten all five

RIP FENCE (#10C)LOCK BLOCK (#7C)REAR RAIL (#3H)SAW TABLEFIGURE KSCALE INDICATOR(#20C)RIP FENCE(#10C)FRONT RAIL(#7H)FINE ADJUSTMENTKNOB (#30C)SAW TABLE

To Assemble And Attach The Bevel And Height Handles To The Base:1. Insert one Screw (part #6G) each through a Bevel Handle and Height Handle(part #5G)

3. Secure the Motor Bracket (part #7F) to the Motor Mounting Plate (part #50-I),using four Hex Head Bolts (part #9-I), eight Washers (part #52-I), fou

2. Secure the Belt Guard (parts #1F, #4F) to the Motor (part #7F), using four FlatWashers (part #3F) and four Hex Nuts (part #2F). (See Figu

SPECIFICATIONS TABLESAVE THIS MANUALYou will need this manual for the safety warnings and precautions, assembly,operating, inspection, maintenance, an

3. Push the Motor (part #7F), with its attached Belt Guard (parts #1F, #4F), forwardand place the V-Belt (part #40-I) on the Motor Pulley (part #5F).

OUTER BLADE WASHER (#15-I)ARBOR SHAFT (#13-I)BLADE NUT (#16-I)10” SAW BLADE(#14-I)FIGURE R3. Reach into the Saw Blade opening and remove the Blade Nut

6. Once the 10" Saw Blade (part #14-I) is secured onto the Arbor Shaft (part #13-I),replace the Throat Plate (part #15H) and tighten the Flat Hea

OPERATING INSTRUCTIONSTo Raise And Lower The 10" Saw Blade:1. When cutting, the top edge of the Saw Blade (part #14-I) should rise about 1/4”abov

3. To adjust the bevel of the 10" Saw Blade (part #14-I), unlock the Bevel Lock (part#19-I). Next, move the Bevel Handle (part #5G) to the right

2. Before each use, inspect the general condition of the 10" Table Saw. Inspect thePower Switch (part #8E), Power Plug and Cord Assembly (part #

'   

 8 =$  8 =$+   +   +  

PARTS LISTSKU 46813 PAGE 28 8 =$  8 =$  ;   ;

 8 =$  8 =$0  0 0  0 0

4. DO NOT USE THIS PRODUCT IF UNDER THE INFLUENCE OF ALCOHOL ORDRUGS. Read warning labels on prescriptions to determine if your judgment orreflexes a

ASSEMBLY DIAGRAM BNOTE: Some parts are listed and shown for illustration purposes only, and are notavailable individually as replacement parts.SKU 46

ASSEMBLY DIAGRAM CNOTE: Some parts are listed and shown for illustration purposes only, and are notavailable individually as replacement parts.SKU 46

ASSEMBLY DIAGRAM DNOTE: Some parts are listed and shown for illustration purposes only, and are notavailable individually as replacement parts.SKU 46

ASSEMBLY DIAGRAM ENOTE: Some parts are listed and shown for illustration purposes only, and are notavailable individually as replacement parts.SKU 46

ASSEMBLY DIAGRAM FNOTE: Some parts are listed and shown for illustration purposes only, and are notavailable individually as replacement parts.SKU 46

ASSEMBLY DIAGRAM GNOTE: Some parts are listed and shown for illustration purposes only, and are notavailable individually as replacement parts.SKU 46

ASSEMBLY DIAGRAM HNOTE: Some parts are listed and shown for illustration purposes only, and are notavailable individually as replacement parts.SKU 46

ASSEMBLY DIAGRAM INOTE: Some parts are listed and shown for illustration purposes only, and are notavailable individually as replacement parts.SKU 46

SPECIFIC PRODUCT WARNINGS AND PRECAUTIONS1. GROUND THIS PRODUCT. The electrical power cord for this product isequipped with a grounded 3-Prong Plug.

7. KEEP ALL GUARDS IN PLACE AND IN WORKING ORDER.8. REMOVE ALL ADJUSTING WRENCHES FROM THE TABLE SAW BEFORETURNING IT ON.9. AVOID UNINTENTIONAL STARTI

20. (Continued) To avoid kickback, keep a firm grip on the workpiece at all times.Support overhanging work pieces; as the work piece is cut and w

UNPACKINGWhen unpacking, check to make sure all parts shown on the Parts Lists (pages 27through 29) are included. If any parts are missing or broken,

FIGURE CSKU 46813 PAGE 8 

ASSEMBLY INSTRUCTIONSNOTE: For additional references to the parts listed below, refer to the AssemblyDiagrams on pages 29 through 37 of this manual.W